Serial Interface \ VOGONS

Serial Interface

Topic actions

Post a reply

First post, by Mallabar

Posted on 2010-11-17, 12:35

Mallabar Offline

Rank Newbie

Rank: Newbie
Posts: 7
Joined: 2010-11-09, 09:03

Hello,

I have a problem concerning the serial Interface.
An Old Software get some Data via COM2, unfortunatly when I start the Software I get the following Message in the Status Window:

Serial1: Errors: Framing 0, Parity 0, Overrun RX:0 (IF0:0), TX:1, Break 0

In the DOSBox Conf I added the following line:

serial1=directseriel realport:COM2

The other serials are all disabled.
The same Message occur, if I use dumme instead of the settings above.
Is there anything I have to do in addition ta make this work?
I get the Same Message when I use COM1.

with kind regards

Reply 1 of 7, by Mallabar

Posted on 2010-11-17, 12:36

Mallabar Offline

Rank Newbie

Rank: Newbie
Posts: 7
Joined: 2010-11-09, 09:03

I use the Megabuild of Version 0.73

Reply 2 of 7, by Mallabar

Posted on 2010-11-23, 07:30

Mallabar Offline

Rank Newbie

Rank: Newbie
Posts: 7
Joined: 2010-11-09, 09:03

Does Nobody have a solution?
Just a small hint would be enough.

with kind regards

Reply 3 of 7, by keropi

Posted on 2010-11-23, 07:33

keropi Offline

Rank l33t++

Rank: l33t++
Posts: 9285
Joined: 2003-09-08, 06:45
Location: Greece

you do realise dosbox was build to play dos games and not applications, right?

🎵 🎧 ⏳ ⚡ PCMIDI MPU , OrpheusII , Action Rewind , Megacard and 🎶GoldLib soundcard website

Reply 4 of 7, by Mallabar

Posted on 2010-11-23, 10:16

Mallabar Offline

Rank Newbie

Rank: Newbie
Posts: 7
Joined: 2010-11-09, 09:03

Ah Sorry,

I didn' know that One forbid the Other 😳

Reply 5 of 7, by Qbix

Posted on 2010-11-23, 10:17

Qbix Offline

Rank DOSBox Author

Rank: DOSBox Author
Posts: 11234
Joined: 2002-11-27, 14:50
Location: Fryslan

try mb6

Water flows down the stream
How to ask questions the smart way!

Reply 6 of 7, by Mallabar

Posted on 2010-11-23, 11:33

Mallabar Offline

Rank Newbie

Rank: Newbie
Posts: 7
Joined: 2010-11-09, 09:03

Thanks,

I will try this as soon as possible

Reply 7 of 7, by Lerche

Posted on 2010-11-30, 09:03

Lerche Offline

Rank Newbie

Rank: Newbie
Posts: 1
Joined: 2010-11-30, 08:59

Hi folks

Sorry to hijack this thread, but it seems that my problem is a lot alike.

I have an old test program, for some electronics, that needs DOS to run. The app runs, but keeps getting me framing errors.
I've setup the serial ports, 1200 8O1, IRQs 4-3-11 for COM1-3.
Every time my equipment is shut down, the program pops up, giving me a framing error, as is the stop bit wasn't received or something. I've look through the forum, but can't find a solution.
I've tried both orig DosBox, and MB6.

Anyone has an idea why this is happening?

Regards

/ Lerche

Go to top of page Go to top of page

Back to DOSBox General

Main menu

Common searches