Try mounting with the -freesize paramter.

By default DosBox only shows 110m free so that old games don't complain, but some newer DOS games do not like this low value so you must make the default vault that DosBox shows bigger.

I use "Mount c c:\games -freesize 999" for these newer DOS games and it works fine.

Ah, that's not hard drive space it's complaining about. It's complaining about RAM. You need to either run "loadfix" or verify that DosBox is set to use 16mb or less of memory.

Ronan:

Please, stop using BMP format for screenshots (It takes up too much space). Use PNG or GIF instead.

ok sorry and and how do i fix the ram part up ??

As DosFreak says, just run "loadfix" before starting the game or, if that doesn't work, edit dosbox.conf, so that "memsize=8" (for example, just make sure that value is 16 or less).

read all replies.

ok i tried what u all said when i put in load fix it said 64kb allocated so yea i changed the config file but nothing so yea

And it still did not run after loadfix AND changing the config file?

didnt i just say that
and in case i didnt yes thats right

Occasionally we get a person posting here with BAK memory problems....which is odd because we never get them. I just searched the forum and either the poster gives up and never posts back or they get their game working but they never post the solution......

Could you post the contents of your dosbox.conf here?

aww this dont sound good for me 😢 😢

oh well im off to bed its 0106 (1:06 am) reply if u find out whats wrong ...

🤣 didnt see that part well here u go [sdl]
# fullscreen -- Start dosbox directly in fullscreen.
# fulldouble -- Use double buffering in fullscreen.
# fullresolution -- What resolution to use for fullscreen: original or fixed size (e.g. 1024x768).
# windowresolution -- Scale the window to this size IF the output device supports hardware scaling.
# output -- What to use for output: surface,overlay,opengl,openglnb,ddraw.
# autolock -- Mouse will automatically lock, if you click on the screen.
# sensitiviy -- Mouse sensitivity.
# waitonerror -- Wait before closing the console if dosbox has an error.
# priority -- Priority levels for dosbox: lowest,lower,normal,higher,highest.
# Second entry behind the comma is for when dosbox is not focused/minimized.
# mapperfile -- File used to load/save the key/event mappings from.
# usescancodes -- Avoid usage of symkeys, might not work on all operating systems.

fullscreen=false
fulldouble=false
fullresolution=original
windowresolution=original
output=surface
autolock=true
sensitivity=100
waitonerror=true
priority=higher,normal
mapperfile=mapper.txt
usescancodes=true

[dosbox]
# language -- Select another language file.
# memsize -- Amount of memory dosbox has in megabytes.
# machine -- The type of machine tries to emulate:hercules,cga,tandy,pcjr,vga.
# captures -- Directory where things like wave,midi,screenshot get captured.

language=
machine=vga
captures=capture
memsize=40

[render]
# frameskip -- How many frames dosbox skips before drawing one.
# aspect -- Do aspect correction, if your output method doesn't support scaling this can slow things down!.
# scaler -- Scaler used to enlarge/enhance low resolution modes.
# Supported are none,normal2x,normal3x,advmame2x,advmame3x,advinterp2x,advinterp3x,tv2x,tv3x,rgb2x,rgb3x,scan2x,scan3x.

frameskip=0
aspect=false
scaler=normal2x

[cpu]
# core -- CPU Core used in emulation: simple,normal,full,dynamic.
# cycles -- Amount of instructions dosbox tries to emulate each millisecond.
# Setting this higher than your machine can handle is bad!
# You can also let DOSBox guess the correct value by setting it to auto.
# Please note that this guessing feature is still experimental.
# cycleup -- Amount of cycles to increase/decrease with keycombo.
# cycledown Setting it lower than 100 will be a percentage.

core=normal
cycles=3000
cycleup=500
cycledown=20

[mixer]
# nosound -- Enable silent mode, sound is still emulated though.
# rate -- Mixer sample rate, setting any devices higher than this will
# probably lower their sound quality.
# blocksize -- Mixer block size, larger blocks might help sound stuttering
# but sound will also be more lagged.
# prebuffer -- How many milliseconds of data to keep on top of the blocksize.

nosound=false
rate=22050
blocksize=2048
prebuffer=10

[midi]
# mpu401 -- Type of MPU-401 to emulate: none, uart or intelligent.
# device -- Device that will receive the MIDI data from MPU-401.
# This can be default,alsa,oss,win32,coreaudio,none.
# config -- Special configuration options for the device. In Windows put
# the id of the device you want to use. See README for details.

mpu401=intelligent
device=default
config=

[sblaster]
# sbtype -- Type of sblaster to emulate:none,sb1,sb2,sbpro1,sbpro2,sb16.
# sbbase,irq,dma,hdma -- The IO/IRQ/DMA/High DMA address of the soundblaster.
# mixer -- Allow the soundblaster mixer to modify the dosbox mixer.
# oplmode -- Type of OPL emulation: auto,cms,opl2,dualopl2,opl3.
# On auto the mode is determined by sblaster type.
# All OPL modes are 'Adlib', except for CMS.
# oplrate -- Sample rate of OPL music emulation.

sbtype=sb16
sbbase=220
irq=7
dma=1
hdma=5
mixer=true
oplmode=auto
oplrate=22050

[gus]
# gus -- Enable the Gravis Ultrasound emulation.
# gusbase,irq1,irq2,dma1,dma2 -- The IO/IRQ/DMA addresses of the
# Gravis Ultrasound. (Same IRQ's and DMA's are OK.)
# gusrate -- Sample rate of Ultrasound emulation.
# ultradir -- Path to Ultrasound directory. In this directory
# there should be a MIDI directory that contains
# the patch files for GUS playback. Patch sets used
# with Timidity should work fine.

gus=true
gusrate=22050
gusbase=240
irq1=5
irq2=5
dma1=3
dma2=3
ultradir=C:\ULTRASND

[speaker]
# pcspeaker -- Enable PC-Speaker emulation.
# pcrate -- Sample rate of the PC-Speaker sound generation.
# tandy -- Enable Tandy Sound System emulation (off,on,auto).
# For auto Tandysound emulation is present only if machine is set to tandy.
# tandyrate -- Sample rate of the Tandy 3-Voice generation.
# disney -- Enable Disney Sound Source emulation.

pcspeaker=true
pcrate=22050
tandy=auto
tandyrate=22050
disney=true

[bios]
# joysticktype -- Type of joystick to emulate: none, 2axis, 4axis,
# fcs (Thrustmaster) ,ch (CH Flightstick).
# none disables joystick emulation.
# 2axis is the default and supports two joysticks.

joysticktype=2axis

[serial]
# serial1-4 -- set type of device connected to com port.
# Can be disabled, dummy, modem, directserial.
# Additional parameters must be in the same line in the form of
# parameter:value. Parameters for all types are irq, startbps, bytesize,
# stopbits, parity (all optional).
# for directserial: realport (required).
# for modem: listenport (optional).
# Example: serial1=modem listenport:5000

serial1=dummy
serial2=dummy
serial3=disabled
serial4=disabled

[dos]
# xms -- Enable XMS support.
# ems -- Enable EMS support.
# umb -- Enable UMB support (false,true,max).

xms=true
ems=true
umb=true

[ipx]
# ipx -- Enable ipx over UDP/IP emulation.

ipx=false

[autoexec]
# Lines in this section will be run at startup.

i wait 10 mins b4 bed for answer other wise it may be a few days (ronan)

1[dosbox]
2memsize=40

Erm... 40 is not less than 16...

Kippesoep wrote:

Erm... 40 is not less than 16...

Depends, 2 + 2 also is 5, with extremely large values of 2 😁

But ontopic, try to add this to your autoexec-part as well:

1[autoexec] 
2# Lines in this section will be run at startup.
3z:\loadfix.com

ok so i did that start up thingy what else ....

ronan wrote:

ok so i did that start up thingy what else ....

Also changed the memsize=40 in the [dosbox]-part to memsize=16?

yep