Re: AMD K6 3DMARK, aiming for stars.

Posted on 2024-05-12, 03:39

by

by Skalabala

in Marvin \ Video

in Marvin \ Video

SWZSSR wrote on 2024-05-12, 01:20: Just had my FIC PA-2013 fully recapped. I luckily have the revision without the weak agp power controller chip that burns out. Will do some benching in the next few weeks once I found a case for it and… time. Is that a 2Mb board?

---

Re: Dead super socket 7 ASUS P5A

Posted on 2024-05-07, 19:31

by

by Skalabala

in Milliways

in Milliways

This board does not turn on the PSU. The power btn pins do not have 5V the reset does though. Board does have slight corrosion though 🙁 🙁

---

Re: Dead super socket 7 ASUS P5A

Posted on 2024-05-04, 16:20

by

by Skalabala

in Milliways

in Milliways

I need to figure out where the power btn get its 5V from.

---

Dead super socket 7 ASUS P5A

Posted on 2024-05-03, 22:20

by

by Skalabala

in Milliways

in Milliways

Hello everyone 😀 So I bought a dead P5A. It does not turn on the PSU. Only thing I found is that the power switch pins on the board does not have 5V. Where do I start 😜

---

Anyone on Commodore.gen.tr forum?

Posted on 2024-05-02, 12:05

by

by Skalabala

in Milliways

in Milliways

Hello everyone, I am trying to get onto this forum but no luck, waiting a week for approval 🙁 There is someone on that forum that has a motherboard that needs to be mine 😜

---

Re: Voodoo 2 SLi hanging up

Posted on 2024-05-02, 11:56

by

by Skalabala

in Milliways

in Milliways

Got a corsair 650W PSU and noting changed. I overclocked each card individually to 100MHz, both had artifacts. The one card now does not work no more it hangs in any game 5 seconds in. Could it be that that card was faulty? TMU dead now? 🙁

---

Cant find old version of CPUCOOL

Posted on 2024-04-27, 22:31

by

by Skalabala

in Milliways

in Milliways

Hello everyone 😀 I am looking for an old version of CPUCOOL that supports ASUS P5A/B I had it and it was version 3.xxx I think 🙁

---

Voodoo 2 SLi hanging up

Posted on 2024-04-23, 12:25

by

by Skalabala

in Milliways

in Milliways

Hello everyone! :) I have been trying for a week now to get my SLi going. Motherboard is P5A-B with K6 3+ 550 and Windows 98SE DirectX 6.1a 7.0 8.0 SLi works with the latest OEM driver and Fastvoodoo 3.5, if I use FV 4.0 or 4.6 then it hangs 1 second into game/3dmark I have not tried any BIOS …

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-22, 11:54

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Its awesome that the PPro had up to 1024kb cache. I always dream of an engineering sample of AMD K6 that was native 133x5.5 extra instructions and 512Kb LOLOL. I mean I can run NFS Most Wanted at 50FPS on my K6. I want to see a P2 Celeron do that!

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-10, 00:18

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Next mod 512kb...

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-09, 12:22

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

The die is 9.20mm by 8.30mm by 0.80mm with error up to 0.02mm

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-06, 17:01

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

analog_programmer wrote on 2024-04-06, 15:53: Skalabala wrote on 2024-04-06, 15:40: I did that, it is 0.80mm Ok, this is height over the ceramic base, but what about length and width of the die? Ok, will get that today and post tonight 😀

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-06, 15:40

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

analog_programmer wrote on 2024-04-05, 05:55: If someone have delided K6-2+ at hand, better off to use caliper to take direct measurements of CPU die. I did that, it is 0.80mm

---

Re: SUCCESSFUL K6-2+ to K6-3+ Full Cache Enable Mod

Posted on 2024-04-05, 02:26

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I measured it and from the ceramic to the top of the die is 0.80mm 😀

---

Re: AMD K6 3DMARK, aiming for stars.

Posted on 2024-04-02, 11:57

by

by Skalabala

in Marvin \ Video

in Marvin \ Video

[/quote] Can you write a guide for that setup? [/quote] I cant remember 🤣 but there is some info on my youtube video of the run. https://www.youtube.com/watch?v=pwG7RtFFXgo

---

Re: FIC 503+ super socket 7 with no cache

Posted on 2024-04-02, 11:53

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I say the date code is a giveaway. Either its cheap or something got fixed in the chipset like ALi with Rev G and H This is the 2003 board. https://allegro.pl/oferta/fic-va-503-plyta-gl … mii-14876863407

---

FIC 503+ super socket 7 with no cache

Posted on 2024-04-02, 01:54

by

by Skalabala

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Hello everyone, hope you are doing well :) Saw this and found it interesting, no cache chips and no TAG chip. Note the date code of the north bridge I did a google search and I found a same one but the date code was 0307! Ebay link, hope its allowed :D https://www.ebay.com/itm/326020694005?epid= …

---

Re: AMD K6 3DMARK, aiming for stars.

Posted on 2024-04-02, 00:05

by

by Skalabala

in Marvin \ Video

in Marvin \ Video

Have not been in this thread for a long while, did anyone beat the scores of Asus P5A boards? They are still my favorite boards and years ago i had many ss7 boards of different brands and Asus boards were faster. Mvp3 didn't come close and while gigabyte (ali V) did clock higher they didn't score …

---

Re: AMD K6 3DMARK, aiming for stars.

Posted on 2024-03-30, 12:13

by

by Skalabala

in Marvin \ Video

in Marvin \ Video

Necrodude wrote on 2024-03-29, 08:06: Has anyone tried the BIOS patcher on the ASUS P5A motherboard? If so, any benefits? I have not, I do not see any benefits though. If I want to mess with BIOS I use TWK153

---

Re: AMD K6 3DMARK, aiming for stars.

Posted on 2024-03-30, 12:09

by

by Skalabala

in Marvin \ Video

in Marvin \ Video

I know there is something weird with those boards and overclocking with cache on. They wont even run at 105MHz. My MVP3GM has two 512kb 4ns chips and it can run 112MHz stable and not 124Mhz You might need to modify the motherboard Don't be discouraged, make it work and teach us :) Socket 7 has came …

---